Zero-residue mold removal for framing, attics and crawl spaces

Dry ice blasting mold WESTLAKE VILLAGE CA without tearing your house apart

When dry ice blasting mold WESTLAKE VILLAGE CA is done right, mold comes off wood framing, joists and ductwork without sanding, soda or water, and without a second mess to clean up. We run dry ice mold remediation in WESTLAKE VILLAGE California for homeowners and property managers dealing with attic mold, crawl space moisture and musty odors after a leak. One visit, one containment, one clean result.

↗
Fast online booking

Request service today

Tell us what is happening. Our local team will confirm your visit shortly.

No spam. No obligation. Just practical help.
Thanks — we'll call shortly to confirm your visit.
Dry Ice Blasting Mold by Mold Remediation Service Westlake Village
Careful work. Honest options.
About this service

What dry ice blasting mold WESTLAKE VILLAGE CA actually does

Dry ice blasting mold WESTLAKE VILLAGE CA is a cleaning method that fires soft dry ice pellets at roughly -109°F through a compressed-air nozzle. The pellets hit mold growth on wood framing, sheathing, joists and ductwork, flash from solid to gas on impact, and lift the mold off the surface. There is no sand, no soda, no water and no chemical slurry left behind. The mold flakes off, we HEPA-vacuum it, and the substrate is left dry and ready for encapsulation.

Local calls usually start the same way: a roof leak in North Ranch, a slow supply-line drip behind a kitchen wall, or crawl space moisture that has been feeding black mold growth for months. We see it in 91361 and 91362 constantly because so much of the housing stock here is 1970s to 1990s wood-frame construction with tight attics. If you have been searching dry ice mold remediation near me WESTLAKE VILLAGE California, this is the service that gets mold off structural lumber without replacing it.

  • ✓ No secondary waste
  • ✓ Wood framing survives
  • ✓ No moisture added
  • ✓ Reaches tight spaces
What's included

What is included in dry ice blasting mold removal

Every dry ice blasting mold WESTLAKE VILLAGE CA job includes inspection, containment, blasting, antimicrobial treatment, HEPA vacuuming and a post-remediation clearance test. Add-ons like duct cleaning, drywall replacement, insulation removal and vapor barrier installation are quoted separately after inspection.

✓

Inspection and moisture mapping

Thermal imaging camera and moisture meter sweep, plus boroscope inspection into wall cavities and ceiling plenums. We log affected square footage and photograph every area before work starts.

✓

Negative air containment

6-mil plastic sheeting, zipper doors and a negative air machine with HEPA filters. A second air scrubber runs inside the work zone. This keeps spores out of the rest of your home during blasting.

✓

Dry ice blasting

Full blasting of affected framing, sheathing, joists and ductwork with a dry ice blasting machine. Mold is lifted off the substrate and captured with a HEPA vacuum as it falls.

✓

Antimicrobial and encapsulant

Antimicrobial solution applied to blasted surfaces, followed by an encapsulant coating on porous or repeatedly wet framing. Products from Fiberlock, Concrobium and Benefect depending on substrate.

✓

Post-remediation testing

Final spore trap and, where needed, InstaScope particle count compared to an outdoor baseline. You get the lab report and a written clearance summary before we invoice.

How it works

How our dry ice mold cleaning WESTLAKE VILLAGE job runs

01

Inspection and testing

We start with a thermal imaging camera and moisture meter sweep, then a boroscope into wall cavities and ceiling plenums. Air samples go to a lab for spore trap analysis, and we log the affected square footage. This stage takes 60 to 90 minutes on a typical Westlake Village home and tells us exactly what we are pricing.

02

Containment setup

We build negative air containment with 6-mil plastic sheeting and run a negative air machine with HEPA filters so spores cannot migrate into the rest of the house. A second air scrubber runs inside the work zone. Setup takes two to three hours and is the step that protects your furniture, HVAC and family.

03

Dry ice blasting

Our technicians suit up in N95 respirators and Tyvek, then blast the affected framing, sheathing and ductwork with a dry ice blasting machine. Most residential attics take four to eight hours. The mold lifts off in flakes, and a HEPA vacuum follows the wand to capture debris as it falls.

04

Antimicrobial and encapsulation

Once the wood is clean and dry, we apply an antimicrobial solution to the blasted surfaces, then an encapsulant coating on framing that has been porous or repeatedly wet. We use products from Fiberlock, Concrobium and Benefect depending on the substrate. This stage takes two to four hours.

05

Post-remediation verification

We run a final spore trap and, where needed, an InstaScope particle count to confirm the air is back to normal. You get the lab report, photos of every stage, and a written clearance summary. If a number is off, we re-clean before we invoice.

Tools & methods

Tools and methods we use on every job

Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.

Dry ice blasting machine

Fires soft dry ice pellets at roughly -109°F to lift mold off framing, sheathing and ductwork without water, sand or soda.

Thermal imaging camera

Finds hidden moisture behind walls and in ceiling plenums before we open anything up, so containment covers the real affected area.

Moisture meter

Confirms wet readings on wood and drywall, and verifies the substrate is dry before we apply encapsulant coating.

Boroscope

Lets us see inside wall cavities, behind baseboards and along duct runs without cutting large access holes.

HEPA vacuum and air scrubber

Captures mold debris and airborne spores during and after blasting. We run ProTeam and Abatement Technologies units inside containment.

Negative air machine

Keeps the work zone under negative pressure so spores cannot migrate into the rest of the house during blasting.

Fogging machine

Treats wall cavities and duct interiors that a blasting wand cannot reach, using a fine antimicrobial mist.

Real results

Before and after.

North Ranch attic after a roof leak

Before

A slow roof leak had been wetting the sheathing and three rafters for about four months. Visible black mold growth covered roughly 180 square feet, and the attic smelled musty every time the HVAC kicked on.

After

We contained the attic, blasted the rafters and sheathing with dry ice, HEPA-vacuumed the debris, and applied antimicrobial and encapsulant. Post-remediation spore counts came back within outdoor baseline, and we saved all the framing.

Foxmoor crawl space with joist mold

Before

Ground moisture had been feeding mold on the joists and subfloor for at least two years. Moisture meter readings on the joists were in the 22 to 26 percent range, and the first floor had a persistent musty odor.

After

We blasted the joists, subfloor and duct surfaces with dry ice, treated with antimicrobial, and installed a vapor barrier. Post-job moisture readings dropped to 11 to 13 percent, and the odor cleared within a week.

Business District mechanical room

Before

A chiller line leak soaked the wall cavity and framing in a mechanical room. Mold had grown on the studs and bottom plate, and the musty smell was reaching an adjacent tenant suite through a shared wall.

After

We set negative air containment after hours, blasted the studs and plate with dry ice, and fogged the cavity. Clearance testing passed on the first try, and the tenant suites had no dust or odor the next morning.

Problems we solve

Mold problems we solve with dry ice blasting

Most dry ice blasting mold removal for attics WESTLAKE VILLAGE California calls come down to one of a few recurring problems. Here is what we see and how we handle it.

Ask a pro →
01

Attic mold from a slow roof leak

We contain the attic, blast the rafters and sheathing with dry ice, HEPA-vacuum the debris, and treat the wood with an antimicrobial and encapsulant. Most jobs finish in one day and save the framing.

↗
02

Crawl space mold on joists and ductwork

We blast the joists, subfloor and duct surfaces, then run a dehumidifier and recommend a vapor barrier. Ductwork that is too far gone gets flagged for replacement rather than cleaned.

↗
03

Mold behind walls after a supply line leak

We open a small inspection access, confirm with a boroscope, then blast the studs and plate with dry ice. Because there is no water or slurry, the cavity dries faster and we close it sooner.

↗
04

Black mold growth on bathroom framing

We remove the affected drywall, blast the framing clean, treat with antimicrobial, and rebuild with moisture-resistant materials. Fixing the source is part of the scope, not an afterthought.

↗
Proof you can check

Licensed, certified, and clearance-tested

✓
IICRC AMRT (Applied Microbial Remediation Technician)Institute of Inspection, Cleaning and Restoration Certification
✓
IICRC WRT (Water Restoration Technician)Institute of Inspection, Cleaning and Restoration Certification
✓
ACAC CMI (Certified Mold Inspector)American Council for Accredited Certification
✓
ACAC CMR (Certified Mold Remediator)American Council for Accredited Certification
✓
California Contractors State License Board (CSLB)State of California
Good questions

Frequently Asked Questions

(833) 929-5837 →

Most residential dry ice blasting mold jobs in WESTLAKE VILLAGE CA run $1,800 to $6,500 in 2026, depending on square footage and access. A single attic with 200 to 400 square feet of affected framing typically lands near the low end. Crawl spaces with ductwork, or jobs that need drywall opened for access, push toward the top. We quote a fixed price after inspection, so the number you sign is the number you pay.

Yes. Dry ice blasting removes mold growth from wood framing, sheathing and ductwork down to the substrate, and it does it without adding water. We follow up with an antimicrobial solution and an encapsulant coating, then verify with a spore trap. On most jobs, post-remediation air samples come back within normal outdoor ranges for Los Angeles County. The key is pairing the blasting with proper negative air containment.

The main benefits are no secondary waste, no added moisture, and less demolition. You keep most of your structural framing instead of replacing it, and there is no sand or soda to sweep up and dispose of. Dry ice also gets into wall cavities and around ductwork where scrapers cannot reach. For a homeowner in Westlake Trails or Foxmoor, that usually means a one-day job instead of a week of demolition and rebuild.

Not when it is run by a trained technician. Dry ice pellets are soft compared to sand or glass media, and the process is non-abrasive on wood, brick, concrete and metal. We dial pressure and feed rate per substrate, and we avoid soft plastics and certain electrical components. In practice, dry ice blasting is gentler on framing than wire brushing or sanding, which is why we use it on structural lumber instead of cutting it out.

Ready when you are

Get a fixed quote for dry ice blasting mold WESTLAKE VILLAGE CA

Call (833) 929-5837 and we will inspect, test and quote your dry ice blasting mold WESTLAKE VILLAGE CA job, usually the same day. Licensed, insured, and clearance-tested before we invoice.

Get My Quote (833) 929-5837 →
Request an appointment

Contact our WESTLAKE VILLAGE team

Call (833) 929-5837 any time, day or night. We answer live, dispatch fast, and cover every neighborhood in WESTLAKE VILLAGE and the surrounding Los Angeles County area. If you prefer email, send us your address and what you are seeing, and we will get back to you the same day.

Request received — our team will be in touch shortly.
Tap to call(833) 929-5837